Engine pull video?

Technical and Repair Discussions

Ready to Write a Book
Ready to Write a Book
Posts: 89
Joined: Fri Apr 22, 2016 5:11 pm
PostPosted: Sun Jan 06, 2019 6:06 pm
Ahoy and Happy New Year. I'm pulling my Gen3 motor to get the transmission overhauled and was wondering if there was a video or a script on how to do it.

I'm curious about the coolant hoses because I'm tempted to leave them (and the tank) attached to the engine when I pull it. If at all possible, I'd like to keep the radiator full throughout the process.

But mainly I'm looking for a video or script to walk me through it.

Regards,
Greg

Novice Typer
Novice Typer
Posts: 18
Joined: Wed Nov 30, 2011 8:00 pm
PostPosted: Sun Jan 06, 2019 10:58 pm
Go the AccelRaceTek.com

Bruce has posted some procedures in his tech section. I have used them as a checklist when pulling my motor.

http://www.accelracetek.com/engine-swap ... es-gen2-3/
User avatar
Needs a Life!!!
Needs a Life!!!
Posts: 714
Joined: Wed Nov 30, 2011 12:21 am

Chassis:
595
PostPosted: Mon Jan 07, 2019 3:38 pm
You will have to unclamp the two hoses running to/from the radiator on both sides of the engine, so draining the coolant is required.

It''s possible to pull the engine with the fill tank and associated hoses remaining attached to the motor. We (Ric Heer at CSR Performance and I) generally remove the coolant fill tank bracket, but leave the intake manifold on (being careful not to damage when pulling). It's also easier (necessary?) to remove the alternator. We then pull the whole engine/transmission out together, angled up on the right side , then disassembing the transmission from the motor while it's hoisted in the air. Ric has an attachment on his shop hoist to dial in a left/right angle as needed when you hoist the motor.

To re-install, we reconnect the motor and transmission before putting back in the car, rather than wrestling with the alignment inside the frame, angling the transmission/engine downward on the transmission side until everything is roughly back place in the frame.

In the field, with a different hoist, we've done it more like Bruce's outline.

BTW, while the transmission is out of the car consider replacing the clutch disc, especially if it's not the newer kind (in any event, check the thickness and any cracks in the plate if you'd rather not.)
Bob Breton - SRF 51 - San Francisco Region

Novice Typer
Novice Typer
Posts: 20
Joined: Fri Dec 02, 2011 2:19 pm
PostPosted: Tue Jan 08, 2019 2:48 am
To Bob Breton,
Next time you pull a motor with the transmission still attached, please take some pictures and post them here or at least send them to me. I know on the gen2 it was tight enough that there was no way to pull a motor with the trans still attached. I'd like to see how much of an angle you have to get it to to pull it or replace it. I am converting a car in the near future so I would like to see what you go through.
Thanks,
Elliott
gutenberg918 at GEE male
User avatar
Ready to Write a Book
Ready to Write a Book
Posts: 83
Joined: Sat May 03, 2014 12:14 pm
Location: Santa Clara, Ca
Chassis:
501
Facebook Page:
http://www.facebook.com/kangamotorsports/
PostPosted: Mon Jan 14, 2019 3:32 pm
You can pull and install the motor and transmission together. You need to remove the right rear rocker and shock to give you the clearance and the angle you need get them in/out.
James Chartres
SRF #82 - Chassis #501
User avatar
Still Learning to Type
Still Learning to Type
Posts: 47
Joined: Wed Sep 24, 2014 9:35 pm
Location: College Station, TX
Chassis:
294
PostPosted: Mon Feb 25, 2019 4:45 pm
I just pulled my engine and transmission last week in one piece without removing the rocker arm...although i did scratch up my new powder coating on the rocker :cry:

here are a few pictures
Attachments
engine pull 2.jpg
engine pull 2.jpg (118.42 KiB) Viewed 1020 times
Engine Pull.jpg
Engine Pull.jpg (120.5 KiB) Viewed 1020 times
Joe Frederick
Texas Region
SRF#65 Chassis#294
User avatar
Still Learning to Type
Still Learning to Type
Posts: 47
Joined: Wed Sep 24, 2014 9:35 pm
Location: College Station, TX
Chassis:
294
PostPosted: Mon Feb 25, 2019 4:47 pm
here are 2 more pics
Attachments
engine pull 4.jpg
engine pull 4.jpg (106.72 KiB) Viewed 1020 times
engine pull 3.jpg
engine pull 3.jpg (120.36 KiB) Viewed 1020 times
Joe Frederick
Texas Region
SRF#65 Chassis#294

Novice Typer
Novice Typer
Posts: 18
Joined: Wed Nov 30, 2011 8:00 pm
PostPosted: Mon Feb 25, 2019 10:44 pm
I have done this with and without removing the RR rocker. With the rocker, I did scratch the paint...agg. Removing the RR rocker makes the pull significantly easier.

Return to Technical and Repair Discussions

Who is online

Users browsing this forum: No registered users and 2 guests